MW10C
With Yamaha's new MW10C USB Mixing Studio mixers, making great music is easier than ever before. Combined with the powerful Cubase AI4 audio/MIDI sequencing software, the new MW series provides a comprehensive tabletop studio setup for the solo recording musician and for the traveling producer/arranger. Connect the new MW to a USB terminal on your laptop or desktop computer, and you've got an instant, high-quality audio recording studio at your command. The MW delivers true plug-and-play USB audio input/output interfacing - without the need for special software drivers - and lets you easily record mono inputs or two- track stereo mixes of multiple sources to your computer.
Features :
- MW12c/MW12cx: 12 audio inputs, 4 featuring inserts and 1-Knob-Compressor
- MW10c: 10 audio inputs, 2 featuring inserts and 1-Knob-Compressor
- MW8cx: 8 audio inputs, 2 featuring inserts and 1-Knob-Compressor
- Stereo output, Monitor stereo output, phones connector
- 2-Track-In analog inputs or via USB from a connected computer
- No driver installation needed, compatible to Windows and Mac
- MW12cx/MW8cx: integrated digital effect unit with 16 programs
- Cubase AI4 included
Specifications :
| Frequency Response |
ST OUT, REC OUT, AUX (EFFECT*) SEND, MONITOR OUT |
-3.0, 0, 1.0 dB, GAIN: min(CH 1-2, CH 3/4-5/6), 20Hz-20kHz, refer to the nominal output level @1kHz |
| Total Harmonic Distortion (THD+N) |
ST OUT |
Less Than 0.1 %, +14dBu, 20Hz-20kHz, Input Gain Control at minimum |
| Hum&Noise |
CH INPUT 1-4 MIC |
-128 dBu, EIN(Equivalent Input Noise): Rs=150ohms, GAIN:max |
| Hum & Noise are measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave attenuation." |
ST OUT, REC OUT |
-87 dBu, ST MASTER CONTROL at nominal level and all Ch level controls at minimum. |
|
AUX (EFFECT*) SEND |
-85 dB, All Ch AUX controls at minimum. |
|
ST OUT, REC OUT |
-64 dB, ST Master control and one Ch level control at nominal level. (CH1,2) |
|
ST OUT |
-100 dB, Residual Output Noise. |
| Crosstalk@1 kHz |
Input to Output |
-70 dB, STEREO L/R, CH 1-2, PAN panned Hard left or right. |
| Phantom Voltage |
MIC |
+48 V |
| USB Audio I/O Sampling Frequency |
|
44.1, 48 kHz, Depend on the application of PC |
| Input HPF |
|
CH 1-2 and CH 3/4-5/6, 80Hz, 12dB/oct |
| Input Equalization +15,-15dB maximum.Turn over/roll-off frequency of shelving:3dB blow maximum variable level. |
High
Mid
Low
High
Low |
10 kHz shelving (CH 1-2, CH 3/4-5/6)
2.5 kHz peaking (CH 1-2, CH 3/4-5/6)
100 Hz shelving (CH 1-2, CH 3/4-5/6)
10 kHz shelving (CH 7/8, CH 9/10**)
100 Hz shelving (CH 7/8, CH 9/10**) |
| PEAK Indicator |
|
Red LED turns on when post EQ (ST CH: or post Mic HA) signal reaches -3dB below clipping (17dBu). |
| Internal Digital Effect |
|
|
16 PROGRAM, PARAMETER control
Foot Switch (Digital Effect, on/off) |
| LED Level Meter |
Pre MONITOR Level |
2x7 points LED meter (PEAK,+6,+3,0,-5,-10,-20 dB)
PEAK lights if the signal comes within 3 dB of the clipping level. |
| Power Supply Adapter |
|
PA-10 |
| Power Consumption |
|
21 W |
| Dimensions |
W x D x H (mm) |
256.6 x 302.5 x 62.2 |
| Net Weight |
|
1.6 kg |
1.7 kg |
| Option |
|
Microphone Stand Adaptor(BMS-10A) |
Microphone Stand Adaptor(BMS-10A), Foot Switch (FC5) |
ANALOG INPUT CHARACTERISTICS(MW10C / MW8CX)
| Connections |
GAIN |
Actual Load Impedance |
For Use With Nominal |
Input Level |
|
|
Connector |
|
|
|
|
Sensitivity *2 |
Nominal |
Max. before clip |
|
| CH INPUT MIC (1, 2) |
-60 dB
-16 dB |
3 k ohms |
50-600 ohms Mics |
-72 dBu (0.195 mV)
-28 dBu (30.8 mV) |
-60 dBu (0.775 mV)
-16 dBu (123 mV) |
-40 dBu (7.75 mV)
+4 dBu (1.23V) |
XLR-3-31 type *3 |
| CH INPUT LINE (1, 2) |
-34 dB
+10 dB |
10 k ohms |
600 ohms Lines |
-46 dBu (3.88 mV)
- 2 dBu (0.615 V) |
-34 dBu (15.5 mV)
+10 dBu (2.45 V) |
-14 dBu (155 mV)
+30 dBu (24.5 V) |
TRS Phone Jack *4 |
| ST CH MIC INPUT (3/4, 5/6) |
-60 dB
-16 dB |
3 k ohms |
50-600 ohms Mics |
-72 dBu (0.195 mV)
-28 dBu (30.8 mV) |
-60 dBu (0.775 mV)
-16 dBu (123 mV) |
-40 dBu (7.75 mV)
-6 dBu (389 mV) |
XLR-3-31 type *3 |
| ST CH LINE INPUT (3/4, 5/6) |
-34 dB
+10 dB |
10 k ohms |
600 ohms Lines |
-46 dBu (3.88 mV)
- 2 dBu (0.615 V) |
-34 dBu (15.5 mV)
+10 dBu (2.45 V) |
-14 dBu (155 mV)
+30 dBu (24.5 V) |
Phone Jack *5 |
| ST CH INPUT (7/8, 9/10 *7) |
|
10 k ohms |
600 ohms Lines |
-22 dBu (61.5 mV) |
-10 dBu (245 mV) |
+10 dBu (2.45 V) |
Phone Jack *5
RCA Pin Jack |
| CH INSERT IN (1, 2) |
|
10 k ohms |
600 ohms Lines |
-12 dBu (195 mV |
0 dBu (0.775 V) |
+20 dBu (7.75 V) |
Phone Jack (TRS) *6 |
| RETURN (L, R) |
|
10 k ohms |
600 ohms Lines |
- 8 dBu (308 mV) |
+4 dBu (1.23 V) |
+24 dBu (12.3 V) |
Phone Jack *5 |
| 2TR IN (L, R) |
|
10 k ohms |
600 ohms Lines |
-22 dBV (79.4 mV) |
-10 dBV (0.316 V) |
+10 dBV (3.16 V) |
RCA Pin Jack | *1: 0 dBu is referenced to 0.775 Vrms. 0 dBV is referenced to 1 Vrms.
*2: Sensitivity is the lowest level that will produce an output of +4 dB (1.23 V), or the nominal output level when the unit is set to maximum level. (all faders and level controls are at maximum position.)
*3: XLR-3-31 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)
*4: Phone Jacks are balanced. (Tip=HOT, Ring=COLD, Sleeve=GND)
*5: Phone Jacks are unbalanced.
*6: Phone Jacks are unbalanced. (Tip=Out, Ring=In, Sleeve=GND)
*7: ST CH IN 9/10 exists only in MW10C
ANALOG OUTPUT CHARACTERISTICS(MW10C / MW8CX)
| Connections |
Actual Source Impedance |
For Use With Nominal |
Output Level |
|
Connector |
|
|
|
Nominal Levell |
Max. before clip |
|
| STEREO OUT (L, R) |
150 ohm |
10k ohms Lines |
+4 dBu (1.23 V) |
+20 dBu (7.75 V) |
Phone Jack *8 |
| AUX SEND (EFFECT SEND *9) |
150 ohm |
10k ohms Lines |
+4 dBu (1.23 V) |
+20 dBu (7.75 V) |
Phone Jack *8 |
| CH INSERT OUT (CH 1, 2) |
75 ohms |
10 k ohms Lines |
0 dBu (0.775 V) |
+20 dBu (7.75 V) |
Phone Jack *6 |
| REC OUT (L, R) |
600 ohms |
10 k ohms Lines |
-10 dBV (0.316 V) |
+10 dBV (3.16 V) |
RCA Pin Jack |
| MONITOR OUT (L, R) |
150 ohm |
10k ohms Lines |
+4 dBu (1.23 V) |
+20 dBu (7.75 V) |
Phone Jack *8 |
| PHONES OUT |
100 ohms |
40 ohms Phones |
3 mW |
75 mW |
Stereo Phone Jack | *1: 0 dBu is referenced to 0.775 Vrms. 0 dBV is referenced to 1 Vrms.
*2: Phone Jacks are impedance balanced. (Tip=HOT, Ring=COLD, Sleeve=GND)
*3: Phone Jacks are unbalanced. (Tip=Out, Ring=In, Sleeve=GND)
*4: EFFECT SEND exists only in MW8CX
MW10C / MW8CX / MW12C / MW12CX System Requirements
| WindowsR Vista |
|
| Computer |
Windows-based computer with built-in USB interface |
| OS |
Windows Vista |
| CPU |
1 GHz or better Intel Core / Pentium / Celeron processor |
| Memory |
More than 1 GB |
| WindowsR XP |
|
| Computer |
Windows-based computer with built-in USB interface |
| OS |
Windows XP Professional / XP Home Edition |
| CPU |
1 GHz or better Intel Core / Pentium / Celeron processor |
| Memory |
More than 128 MB |
| MacintoshR |
|
| Computer |
Macintosh computer with built-in USB interface |
| OS |
Mac OS X 10.3.3 or higher |
| CPU |
Macintosh G3 processor 300 MHz or better |
| Memory |
More than 128 MB |
Cubase AI4 System Requirements
| WindowsR |
|
| OS |
Windows XP Professional / XP Home Edition |
| CPU |
Intel Pentium 1.4 GHz or better |
| Available Memory |
More than 512 MB |
| Hard Disk |
Free disk space of 400 MB or more; high-speed hard disk |
| Audio Interface |
Windows DirectX / ASIO compatible |
| MacintoshR |
|
| OS |
Mac OS X 10.4 or higher |
| CPU |
Power Mac G4 1 GHz or Core Solo 1.5 GHz or better |
| Available Memory |
More than 512 MB |
| Hard Disk |
Free disk space of 400 MB or more; high-speed hard disk | |
